LK3Manual en - Historia wersji

TomekO: /* PINS and COMPONENTS DESCRIPTION */

2017-06-22T08:17:48Z

‎PINS and COMPONENTS DESCRIPTION

2017-03-18T15:59:44Z

‎LAN Controller V3.0

2017-03-18T15:59:23Z

‎Lan Controller V3

2017-03-18T15:58:40Z

‎LAN Controller V3.0

2017-03-18T10:46:27Z

‎INPUT / OUTPUT:

2017-03-18T10:30:48Z

‎NUMBERS OID for SNMP

2017-03-18T10:30:33Z

‎Switching sockets http request

2017-03-18T10:30:14Z

‎Reading XML data

2017-03-18T10:14:44Z

‎INPUT / OUTPUT:

2017-03-18T10:13:22Z

‎INPUT / OUTPUT:

@@ Linia 116: / Linia 116: @@
 ==PINS and COMPONENTS DESCRIPTION==
 {|
 |'''PIN/Component'''||'''   Description'''
@@ Linia 163: / Linia 166: @@
+}
 GND SPI_SDO SPI_SCK SPI_SDI SPI_CS +3,3V
 GND RX TX +3,3 V +5 V
 Console pins
@@ Linia 179: / Linia 184: @@
 voltage and only the controlled from Lan Controller.
 NO C NC
 RESET BUTTON
 Pressing for about 0.5 seconds to change state relays, and hold for longer - up to around
 five seconds will change all settings (both network and configuration) on the factory reset.
 Confirmation of the settings is fast switching on and off the relay (click-click), not to be
 confused with the change of status and exclusion of the relay after a reboot.
 login as an administrator: user: admin password: admin
 IP: 192.168.1.100
 IDC10-1
 – +5V
@@ Linia 225: / Linia 235: @@
 DESCRIPTION OF CONNECTORS:
 RJ12 6P6C (1-wire bus), IDC10-1, IDC10-2:
-manual LAN Controller V3.0 – LANKON-008
-−
 IDC10-2 socket: Connection OUT1÷OUT4
 OUT1÷OUT4 are open collector, it means that the switching means connecting mass of

@@ Linia 2: / Linia 2: @@
 == LAN Controller V3.0 ==
-'''Manual'''
 '''Lan Controller V3''' is a completely new version of device produced from 2011y.

@@ Linia 4: / Linia 4: @@
 '''Manual'''
-== Lan Controller V3 ==
+'''Lan Controller V3''' is a completely new version of device produced from 2011y.
 A small board works as a web server which presents the various sensor readings: temperature,
@@ Linia 22: / Linia 21: @@
 Specific functionality of '''MQTT protocol''' allow control outputs from Internet even if device
 is located in local network behind router.
 ==Example of applications==

@@ Linia 92: / Linia 92: @@
 * dimensions: 67 x 68 x 39 mm + DIN socket (can be mounted on DIN rail)
 ===INPUT / OUTPUT:===
-;4 ANALOG INPUTS INPA1÷INPA4 WITH AMPLIFIER - 2 input voltage ranges:
+*4 ANALOG INPUTS INPA1÷INPA4 WITH AMPLIFIER - 2 input voltage ranges:
 The scope of of measured voltage for a range of 3.3 V
 :gain=1 from 0 to 3300 mV

@@ Linia 979: / Linia 979: @@
 http://192.168.1.100/outs.cgi?pwm0=1 – turn on pwm0 <br/>
-=='''NUMBERS OID for SNMP'''==
+==NUMBERS OID for SNMP==
 OUT0÷OUT5 and PWM0÷PWM3 can read and write, the rest is read only.

@@ Linia 957: / Linia 957: @@
 More XML files will be published in a special document describing how to create your own website using the generator Web and XML files.
-=='''Switching sockets http request'''==
+==Switching sockets http request==
 The current version allows you to control via http commands with browser bar or other

@@ Linia 939: / Linia 939: @@
 reset Lan Controller.
-=='''Reading XML data'''==
+==Reading XML data==
 Reading is possible or if the authorization is disabled and we are already logged in.

@@ Linia 117: / Linia 117: @@
 :-OC output of 100 mA, controlled downside to switching relays, transistors, etc.
 *4 PWM OUTPUT:
-:-the output frequency range of 50 Hz to 100 kHz
+:the output frequency range of 50 Hz to 100 kHz
 *UART - serial - console preview functioning of the Lan Controller system:
-:-Transmission parameters: 115200 bitrate, 8 N 1
+:Transmission parameters: 115200 bitrate, 8 N 1
 ==PINS and COMPONENTS DESCRIPTION==

@@ Linia 95: / Linia 95: @@
 The scope of of measured voltage for a range of 3.3 V
 :gain=1 from 0 to 3300 mV
-:-gain=10 from 0 to 330 mV
+:gain=10 from 0 to 330 mV
 :gain=50 from 0 to 60 mV
 :The scope of of measured voltage for a range of 33 V